Enable ImageMagick perl module for perl/cgi script.
1. Install ImageMagick-perl package corresponding to ImageMagick rpm installed on the server shipped by OS vendor.
e.g.
# rpm -q ImageMagick
ImageMagick-6.0.7.1-12
#rpm -ivh ImageMagick-perl-6.0.7.1-12.i386.rpm
OR
1. You can use up2date or yum to install/upgrade ImageMagick-perl package
# up2date ImageMagick-perl
or
#yum install ImageMagick-perl
2. Run ensim through maintenance mode.
set_pre_maintenance
set_maintenance
set_post_maintenance
service webppliance restart
Reference: http://parallels.com
Tags: enable, ImageMagick, module, Perl, perl/cgi, Script
Bandwidth is getting calculated higher than expected in Ensim Pro for Linux
For RHEL4, Cent OS 4.1, Cent OS 4.2, Cent OS 4.3:
http://download.swsoft.com/ensim/download/pro/linux/4.1.0/hotfix/bandwidth2/rhel4/webppliance-bandwidth-4.1.0-38.rhel.4ES.i386.rpm
Installation Procedure:
rpm -Uvh webppliance-bandwidth-4.1.0-38.[os version].i386.rpm
service webppliance restart
service bandwidth_manager restart
service [affected service] restart (where affected services are proftpd, sendmail, ssh)
Reference : http://parallels.com/
Tags: bandwidth, Ensim Support, expected, Higher, linux, Pro, than
Installation issues on CentOS for Ensim Pro Linux
Since a minimal OS installation for CentOS don’t install prerequisites packages for Ensim Pro X 10.0.0, it is mandatory to create CentOS repos on the local drive or provide an external repos while installing Ensim Pro X 10.0.0
e.g.
python ./ensim-installer.py –adminemail=admin@email.com –adminname=admin –adminpasswd=password –updater=yum –os-source=http://mirror.centos.org/centos/4/os/i386/ –updates-source=http://mirror.centos.org/centos/4/updates/i386/
OR
python ./ensim-installer.py –adminemail=admin@email.com –adminname=admin –adminpasswd=password –updater=yum –os-source=file:///path/to/repos/os –updates-source=file:///path/to/repos/updates
Tags: Centos, Ensim Support, Installation, linux, Pro
Instructions for deleting the swap file after import in Ensim
Eg. partition - /dev/hda3 mounted on /, swap file - /var/swapfile.
Turn off swapping for file “/var/swapfile” with the following command:
swapon, swapoff - enable/disable devices and files for paging and swapping
Swapoff disables swapping on the specified devices and files. When the -a flag is given, swapping is disabled on all known swap devices and files (as found in /proc/swaps or /etc/fstab)
Delete the file “/var/swapfile” with the following command:
Tags: deleting, Ensim Support, file, import, Instructions, swap
Instructions to setup swap file
Select the partition where you want to create the swap file. This partition must have free disk space to create the swap file.
Create a file for swap with the following command (# is shell prompt):
#dd if=/dev/zero of=/var/swapfile bs=1024 count=[count]
where [count]= number of 1024 blocks required. If count=1024000 size of /var/swapfile will be 1024* 1024000 = 1 GB .
You can decide the size of “/var/swapfile” depending on the size of the backup tar file.
Setup an extra swap with the following command:
Enable “/var/swapfile” for swapping with the following command:
Verification: The file “/proc/swaps” must contain the entry for the swap file “/var/swapfile”. If this entry is not present, then swapping has not been enabled for the swap area.
Tags: file, Instructions, Setup, swap
